On A Higher Note Logo, treble clef and stave

Home About Us What's New Contact Us               

L-590Ax, Pure Class A Integrated Amplifier

 The first in the new x series, the L-590Ax is a fully balanced design. The L-590Ax has all the performance of high-end audio in one elegant & convenient package.

 

/images/product_categories/L590AX_front_small.jpg

Luxman introduced the L-550A and L-590A in 2005, since then we have celebrated our 80th anniversary with commemorative components that have reaffirmed Luxman's status at the pinnacle of high-end audio. In these latest integrated models, the gorgeous texture and three-dimensional performance of our original Class A amplifiers has been retained and further refined. For example, the L-550A II amplifiers featured a new electronic selector switch, adopted from the input section of the C-1000f control amplifier; while the 'x' series now uses a variation of the LECUA discrete volume control first introduced in the C-1000f.

Chassis bases have superb vibration absorption in order to surpress noise levels. The power transformer, electrolytic capacitors and amplifier output stage (see amp block below) are laid out so as not to interfere with each other. To reduce interference further, the block construction isolates each section using shielding panels, and extensive internal filtering to reject magnetic flux interference.

/images/product_categories/L590AX_power_block_small.jpg

Pure Class A

Thanks to the always-on nature of the topology and  the removal of an entire type of distortion, allied to sound that excels in a midrange liquidity, low-level detail, superb dynamics and transparency, its devotees are more than happy to put up with low efficiency and heat. What Class A always seems to offer above everything else is a tube-like sound without the maintenance hassle of tubes.

/images/product_categories/Class_A_small.jpg 

Input Selector 

The L-590Ax, L-550Ax and the L-509u, feature the new high quality electronic selector switch, which is the heart of the C-1000f pre-amp (one of Luxman’s 80th anniversary commemoration models). The sound quality deterioration using the new electronic input switch is now minimal, while channel separation and crosstalk efficiency were raised substantially in comparison with the L-550A / L-590A. In addition the illuminated position indicator around the input selector knob, makes it much easier to view the selected position even from afar.

 

/images/product_categories/L590AX_lecua_small.jpg               

Volume Control 

The integrated amplifiers also benefit from the C1000f in that they use a variation of the LECUA 1000 volume control. At any single volume setting only a few resistors are in circuit per channel. The less devices in the signal path, the purer the sound, the cleaner the music.

At low listening levels, potentiometers have trouble keeping both channels in balance,  so one channel might easily be 3dB louder than the other. With the volume control made of discrete parts, this is no longer an issue. 

 

 /images/product_categories/L590AX_inside_small.jpg

 

Amplifier 

The amplifier section has not been ignored either; noise and distortion has been kept to a minimum with the introduction of ODNF version 3.0A. The deep, rich Class A tone is available here is Luxman’s hall-mark sound. More info on ODNF below.

/images/misc/ODNF.jpg

ODNF
 
Luxman holds many patents for audio engineering, amongst them is the application of Global Negative Feedback to the output stage, which while widely used throughout the audio industry, they no longer use themselves.

Luxman nowadays use a distortion reduction circuit called Only Distortion Negative Feedback (ODNF). This system works by isolating noise & distortion at the output from the music signal and sparingly applying negative feedback to suppress them. Conventional negative feedback systems can have an adverse effect on the music, introducing phase distortion. "The circuit features such an ultra-wide range, ultra- high slew rate and ultra low distortion that it does not use phase compensation for the music signal amplifying circuits." This new technology also ensures that need for a DC servo circuit is alleviated, again improving sound quality.

 

 

/images/product_categories/L590AX_trans_small.jpgCustom transformer, custom capacitors

Pure Copper Cabling 

Extensive listening was applied to the high purity, oxygen free copper (OFC) cables which are used to transmit the signal throughout the amplifier. These cables have a minimal audible signature and minimal electrical effect on the audio waveform. Linear wide bandwidth frequency response is achieved by the low measured values of both inductance and capacitance. The result, the cables do not color the sound, but pass it through, quickly.

 

Phono Amplifier  

Enjoy the ability to play or record your LP collection with the built-in phono stage which accommodates both Moving Magnet and Moving Coil cartridges. The MM input has approx. 35dB of gain. While the MC input has 55dB of gain (a multiplication of 550x). We recommend MC cartridges with an output >.25mV. Lower than that you might consider using the MT-88 moving coil step-up transformer. Click here to be redirected.

 

Subsonic Filter

A subsonic filter is also easily accessible from the remote control in order to remove unwanted low frequency noise while you are listening to a record. When the stylus hits the groove, you might notice the woofers modulating in and out, even though there is no music playing yet. This is due to the ultra low frequency information (below the music), this unnecessary information places a strain on the amplifier and is best filtered out. A mono switch is also available for both loudspeaker setup as well as mono record playback. Both the Mono & Subsonic filter are accessible from the remote control.

 

Headphone Amplifier

There is also a high quality headphone amplifier, accessible from the front panel, ideal for late night listening. You can turn off the speaker output by a simple click of the Speaker Selector.

The headphone outlet sees the same signal as the speaker terminals, there is one resistor per channel in the signal path to pad down the output.

 

/images/product_categories/L590AX_rear_term_small.jpg

Two Pairs of Speaker Terminals 

Large speaker terminals for driving two individual sets of speakers. At the turn of the speaker switch, it is possible to change between the two pairs of speakers easily. In addition, if the A+B function is used; Takasina capacitors are used to parallel the output which permits bi-wiring a single pair of speakers.

 

/images/product_categories/L550AX_tone_controls.jpg

Tone Controls 

The tone controls might seem like an anachronism in this day and age of minimalism, but they can be remarkably effective in bring to life a less than perfect music collection. We all have music gems in our collection that are sonicly challenging. A lot of the 1980's CDs are quite harsh sounding and the digital glare can be quite fatiguing. Reduce the treble slightly and while the harsh CD is not going to suddenly sound like a reference recording, at least it will now be perfectly listenable. Sit back relax, enjoy the music & forgot about the HiFi. When you want to bypass the tone controls, just engage the Line Straight switch, either from the remote control or from the front panel.

 

NOTE:          You might also use the Tone Controls for room acoustics’ correction. They are in effect simplified room equalization controls.

 


 

/images/product_categories/L590AX_remote_RA17_small.jpgRA-17 remote control not only handles Mono, Line Straight (tone controls defeat), Separate (Home Theater Processor Bypass), Subsonic (rumble filter for vinyl playback) and even Loudness (mild boost of bass & treble for low level listening).

The RA-17 also controls the main functions of the Luxman D-05, 06 & 08 CD / SACD players. 

 

/images/product_categories/L590AX_rear_small.jpg

 

 

SPECIFICATIONS

 

 

Rated Output

2 x 30W RMS/8Ω 2 x 60W RMS/4Ω

Input sensitivity/impedance

Phono (MM): 2.5mV/47kΩ


Phono (MC): 0.3mV/100Ω


Line: 180mV/42kΩ

Total harmonic distortion

<0.005%

Frequency response

Tone Controls

20Hz ~ 100kHz (-3dB)

Bass ±10dB at 100Hz and Treble ±10dB at 10kHz

S/N ratio

107dB

Line inputs

4 x LINE, 2 x Balanced, 1 x MM/MC (switchable),


1 x TAPE, 1 x Power Amp in

Line outputs

1 x Pre-Amp out, 1 x TAPE, 1 x headphones

Speaker outputs

Speaker A/ B switchable, Speaker A+B

Dimensions (W x H x D)

440mm x 193mm x 463mm (including control knobs and terminals)

17.3 x 7.6 x 18.2"

Weight

28.2kg (62 lb.)

Accessories

Metal remote control handset, polarized power cord

* Features and specifications are subject to change without prior notice.

 



 
 
 

© Copyright On A Higher Note, LLC 2013
On A Higher Note Phone +949-544-1990